Wood Carving Supplies Tyler TX

This page provides relevant content and local businesses that can help with your search for information on Wood Carving Supplies. You will find informative articles about Wood Carving Supplies, including "Carving 101". Below you will also find local businesses that may provide the products or services you are looking for. Please scroll down to find the local resources in Tyler, TX that can help answer your questions about Wood Carving Supplies.

The Home Depot
(903)581-8513
3901 Old Jacksonville Hw
Tyler, TX
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

ABC Supply Co.,Inc/Tyler
903-595-4930
4420 Highway 31 West Tyler, TX, 75709
Tyler, TX
 
EAST TEXAS STAPLE & SUPPLY
(903) 939-9000
15989 FM 2493, UNIT D TYLER, TX, 75703
Tyler, TX
 
Broadway Square
(903) 534-2334
4701 S Broadway Ave
Tyler, TX
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:12-18
Store Features
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:12-18

Lowe's
(903) 579-2470
3200 South Main Street
Lindale, TX
Hours
M-SA 7 am - 9 pm
SU 8 am - 8 pm

Sam R Hill Lumber Co
(903) 593-8266
1124 E Erwin
Tyler, TX
 
Southern Fastening Systems- Tyler
903-561-0103
13154 Highway 155 S Suite B Tyler, TX, 75703
Tyler, TX
 
Lowe's
(903) 581-8500
5720 South Broadway
Tyler, TX
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

LOWE'S OF TYLER, TEX.
903 581-8500
5720 SOUTH BROADWAY TYLER, TX, 75703
Tyler, TX
 
Miller Hardware
(903) 849-6116
108 Dobbs Street
Chandler, TX
 

Carving 101

Please welcome guest blogger, Kari Hultman from The Village Carpenter . Kari’s attention to detail and humble personality make her blog one of the best on the web! She was kind enough to give us the scoop on carving. I hope you enjoy.

There are several types of wood carving: letter, chip, and relief carving; and carving in the round. Carving tools include knives, chisels, gouges, and mallets. For carving in the round, rasps and files are helpful. Gouges come in many shapes and are gauged by their width and sweep (the amount of curve on the cutting edge). Included in the mix are straight, bent, fishtail, in-cannel (the bevel is on the inside rather than the outside), spoonbit, and V-gouges. Many are also available with short or long handles.

Which Tools To Buy

Like any new woodworking venture, it can be a little daunting to know where to start. Several woodworkers have emailed me with questions about which tools they need to carve wood. They ask if it’s best to invest in a set of carving tools. My response is always the same: find a project you like—from a book or magazine—and purchase the tools you need to carve it. Publications will often provide you with a checklist of tools for the project. Chances are you’ll use those tools again because you used them to carve a project you like. Whereas, when you buy a set, there will be one or more tools you will never use.

Now, what type of carving would you like to try?

Chip Carving

Chip carving is the easiest. You need only two tools—a primary knife and a stab knife. Chip carving consists of three basic, rather shallow cuts. Once you master them, you need only arrange them to create your own designs.

Letter Carving

Letter carving can be complex or easy. You can use a large variety of chisels and gouges which match every conceivable shape you need. Or, you can simply use a chip carving knife. With chip carving, however, you will be limited by the type of wood (certain hardwoods can very difficult) and the size of the letters. Instead, use a different technique which requires only one chisel and one shallow-sweep gouge. The size of the tools depends on the size of the letters. With this technique I can carve just about any type of wood and any size or shape letter.

Relief Carving

Relief carving is where you start getting into some money. I do not have a huge variety of gouges, and try to make do with what I have. As you begin to carve, you will realize what you’re missing from your collection. Keep in mind, just as you don’t need to have chisels ranging from 1/16” to 2 1/2” and everything in between, you can often get by with less.

Carving in the Round

Carving in the round is like relief carving only the project is carved on all sides, as with a ball-and-claw foot (the image to the left is borrowed from the internet). Rasps can remove lots of wood in short order, and files refine the shape. There is nothing quite as luminous as the smooth facets left by a ch...

Click here to read the rest of this article from The Wood Whisperer


 
Copyright © 2006-2013 The Wood Whisperer. All rights reserved.
Designed and Developed by Underscorefunk Design